Home-automation RC-2000 Manuel d'utilisateur

11 RC-2000 Thermostat Installation Instructions DESCRIPTION The RC-2000 is a precision digital thermostat designed for 24 VAC he

1100 Heat Pump (2 Stage Heat / 1 Stage Cool) 24VAC Common*24VAC "HOT"Auxilirary HeatCompressorGround FaultHumidifierFanDehumidierCompressor

1111 Two Speed Heat Pump (3 Stage Heat / 2 Stage Cool) Comp Stage 2 RelayComp Stage 1 RelayCompressor Stage 2954138671112(D)(H)(L)(G)(Y1)(B)(O)(W2)(C

1122 REMOTE SYSTEM WIRING DIAGRAMS This thermostat has been preprogrammed with energy saving program schedules. When used with a remote system, HAI

1133 HAI HOME CONTROL SYSTEMS The thermostat can be connected to an HAI Home Control system. The controller can send commands to the thermostat to c

1144 REMOTE SETBACK SWITCH The thermostat can be connected to a remote switch to toggle the desired heat and cool temperature settings between preset

1155 REMOTE TEMPERATURE SENSOR A remote temperature sensor can be installed to monitor the temperature from a remote location or can be combined with

1166 DISABLE LOCAL CONTROL The Task Buttons and Scroll Wheel on the thermostat can be disabled to prevent anyone from controlling the thermostat loca

1177 SETUP AND CONFIGURATION NOTE: For proper operation of the features of this thermostat, the Time and Date must be set. Even when connected

1188 System Options Note: Before operating the thermostat, the “System Type” and “System Mode” must be configured. The thermostat can be configured

1199 Cool/Heat Min On/Off These items are used to limit the on and off times of the cooling and heating system (in minutes). Cool Minimum On The n

22 Location When replacing an existing thermostat, install the RC-2000 in the same location. If the existing location doesn't meet the followin

2200 EEC Control The EEC Settings are used to configure Energy Efficient Control, 2nd Stage Differential, and Auxiliary Heat Differential. Not all o

2211 Anticipator Control The Anticipator Control settings are used to “anticipate” the need to turn the system on or off before the temperature is a

2222 Temperature Sensors The Temperature Sensor settings are used to configure the internal temperature sensor and optional remote temperature sensor

2233 Emergency Heat Options The Emergency Heat Options are used to reconfigure the H (Humidifier) or D (Dehumidifier) outputs on the RC-2000 to activ

2244 TROUBLESHOOTING TIPS SYMPTOM ACTION TO TAKE Thermostat Dead 1. Check power to the thermostat 2. Check wiring diagrams SYMPTOM ACTION TO

33 Connect each wire to the terminal strip(s) on the thermostat base per the wiring diagram for your system application - See Figures 4 - 10. Form t

44 TYPICAL WIRING DIAGRAMS CAUTION: Do not short gas valve, fan, heat relay, or cool relay...even momentarily. Do not attempt to h

55 3. When configured as a conventional thermostat, by default this thermostat does not turn the fan on with a call for heat. If the furnace requir

66 Single Stage Conventional 24VAC "HOT"Heat24VAC Common*FanCoolHumidifierDehumidierUP24VACCONTROLTRANSMFOMERDehumidifierHumidifierFan Rela

77 Single Stage Conventional for Zone Control Systems (W2)4(Y2)(D)(H)(G)(Y1)(W1)(C)(RC)10138671112ZONE CONTROLLERTHERMOSTATDehumidifierHumidifierSyst

88 Two Stage Conventional (2 Stage Heat / 2 Stage Cool) UPHeat 1Heat 224VAC Common*24VAC "HOT"DehumidierHumidifierCool 2Cool 1Fan24VACCONTR

99 About Heat Pump Systems 1) Terminal 5 (O) is energized for cooling Terminal 6 (B) is energized for heating In most applications, the reversing